MATERIAL SAFETY
TEC-N-TEC INC.
DATA SHEET
8244 PASCAL-GAGNON
ST-LEONARD, QC H1P 1Y4
TEL. (888) 832-7777
EMERGENCY TEL: CANUTEC (613) 996-6666
Identification NO : TB1741
Issued date: December 23, 1996
Revised: July 07, 2005
By: N. Bibeau
By: D. Laplante
1. PRODUCT IDENTIFICATION
ETHYL CYANOACRYLATE GLUE
CASE N/
2. HAZARDOUS INGREDIENTS
%
OSHA PEL
ACGIH TLV
AUTRES
Alpha Ethyl Cyanoacrylate
7085-85-0 95-98
S/O
S/O
4ppm
Méthacrylate de poly-méthyle
9011-14-7 2 - 5
S/O
S/O
S/O
3. PHYSICAL AND CHEMICAL DATA
Boiling point:....................................
65.5°C at 6 mm Hg
Approximately -40/C
Melting point:....................................
2 @133/F
Vapour pressure(mm/hg):...............
Evaporation rate:..............................
Slow
Water solubility:...............................
Insoluble
Specific gravity:...............................
1.04 (Water = 1)
Volatility (%):....................................
UN
Volatile organic compounds:..........
N/Ap
PH:.....................................................
N/Ap
Viscosity:..........................................
5 cps max.
Appearance / Odour...........................
Clear liquid (transparent), Pungent odour
4. FIREFIGHTING MEASURES AND EXPLOSION DATA
Flash point:.......................................
83°C (Closed cupel)
Flammable limits:.............................
Lower limit: N/Ap
Upper limit: N/Ap
Flammable temperature:.................
N/Ap
Extinguishing media:.......................
Foam, carbon dioxide or dry chemical
Special firefighting procedures:.....
Firefighters should be equipped with self-containing breathing apparatus. Water will
intensify polymerization with liquid.
Fire and explosion hazards:............
Flammable. Stored containers near heat or fire may explode due to inside pressure
caused by heat.
NFPA code for hazardous
compounds:.....................................
UN
Unusual reaction risk:.....................
None
5. STABILITY AND REACTIVITY DATA
Stability:............................................
Stable
Material to avoid:..............................
Water, weak base, alcohols, heat
Dangerous polymerization:.............
Likely to take place
Reactivity:.........................................
Moisture, water, excess heat, stay open
Hazardous decomposition
products:...........................................
Acid, carbon monoxide, carbon dioxide, cyanide compound
Abbreviations:
N/A - Not available
N/Ap - Not applicable
UN - Unknown
.../2
page 2
Identification N/: TB1741
6. ENVIRONMENT INFORMATION
Corrective measures when spilled: Consider every measure explained in other sections. Eliminate all source of ignition.
Evacuate the area, recover as much material as practical, soak up the remainder with absorbent materials. Ventilate the area.
Wear self contained breathing apparatus, rubber boots and polyethylene gloves when cleaning up.Waste disposal method:
Dispose in conformity with local municipal by-laws and Environment Ministry rules and recommendations.
7. FIRST-AID MEASURES
Eye contact:.......................................
Hold eyelid open and flush with water for 15 minutes, See a doctor at once.
Skin contact:......................................
In case of skin contact, soak in warm water and do not pull. Use acetone as a remover.
See a doctor if irritation persists. Wash all clothing before wearing it again.
Inhalation:..........................................
In case of inhalation, move victim to fresh air.
Ingestion:...........................................
Do not induce vomiting. In case of vomiting, maintain head lower then hips to avoid
vomit to reach lungs. Get medical attention immediately.
Other first-aid measures:..................
None.
8. TOXICOLOGICAL PROPERTIES
Route of entry:...................................
Inhalation, skin contact, ingestion
Toxicity:..............................................
Oral (LD50): N/A
Skin (LD50): N/A
Vapour (LC50): N/A
SIMDUT CLASS:.................................
B3 - D2B
Chronic effects on humans:.............
Not known
Acute effects on humans:.................
Eye irritation, bonds skin instantly.
9. PREVENTIVE MEASURES FOR STORAGE AND HANDLING
Required conditions for EPP:...........
Normal working conditions
Eye protection:...................................
Wear safety glasses with side shields. Avoid direct eye contact
Gloves requirements:........................
Using polyethylene gloves is recommended
Clothing requirement:.......................
For a long exposure, wear rubber boots and waterproof clothes
Respirator requirements:..................
Use an approved NIOSH respirator
Technical control:..............................
Local exhaust recommended. Mechanical exhaust recommended in storage room
Storage:..............................................
Keep container closed while not in use. Keep away from heat, flashes and flames.
Store in a cool place.
10. NOTICE
All statements, recommendations and technical information contained in this document are based on data supplied by the manufacturer
which Tec-N-Tec believes to be accurate as of this date. The buyers however should test this product before use. Tec-N-Tec will assume
no obligation or liability for results obtained from the use of this product. The product and information herein are believe to be accurate.
Tec-N-Tec will not be liable for any direct or indirect use and or any other damage whatsoever, except to replace the product and or refund
the purchase price to the purchaser.