Adhertec 112201 Material Safety Data Sheet (MSDS)

FICHE SUR LA SÉCURITÉ TEC-N-TEC INC.

MATERIAL SAFETY DATA SHEET

TEC-N-TEC INC

8244 rue PASCAL-GAGNON

ST-LÉONARD, QUE. H1P 1Y4

TEL. (514) 325-7777

EMERGENCY TEL. (613) 996-6666

Adhertec: N° 112201

Issued date: May 28, 1997 Revised: July 07, 2005

By: N. Bibeau By: D. Laplante

1. PRODUCT IDENTIFICATION

Pressure sensitive water base adhesive

2. HAZARDOUS INGREDIENTS Case n° % OSHA PEL ACGIH TLV OTHERS

Vinyl acetate 0-21-04108-4 n/a n/a n/a

3.PHYSICAL AND CHEMICAL DATA

Boiling Point:........................ 100°C Vapour Pressure (mmhg):....... Like water Evaporation Rate:.................. Like water Water solubility:.................... Miscible in cold or warm water

Specific gravity:.................... 1.05(water = 1)

Volatility (%):....................... N/A

Volatiles organic compounds: N/A

PH:...................................... 5

Viscosity:............................. 3000 cps (Brookfield #4 spindle @ 60rpm

Appearance/odour:................ Milk white aqueous emulsion, mild odour.

4.FIREFIGHTING MEASURES AND EXPLOSION DATA

Flash Point:.......................... 100°C (Closed cell)

Explosive Limit:.................... Lower Limit: N/Ap

Upper Limit: N/Ap

Extinguishing media:.............. Water and Carbon Dyoxide

Special firefighting procedures: Fire fighters should be equipped with self-contained breathing apparatus to

protect against potentially toxic and irritating fumes..

Fire and explosion hazards:....... Inflammable. No unusual hazards are expected. Only the solids will burn.

NFPA for hazardous compounds: N/A

Hazardous combustion products: None

5. STABILITY AND REACTIVITY DATA

Stability:..................................... Stable

Material to avoid:......................... Water reacting material

Polymerization: ........................... Will not occur

Reactivity:.................................. Non - available

Hazardous decomposition products: Non-available

6. SPILL OR LEAK PROCEDURES

Spill or leak procedures: Take precautions like described in the other section.

Spill or leak: dilute with water and absorb with a mop or absorb with an inert dry material and put in a plastic container. Recommended waste disposal: It would be recommended to recover or incinerate the product in an approved waste disposal area in accordance with Provincial and Local rules.

7. FIRST-AID MEASURES

Eye contact:..................................... IMMEDIATELY flush eyes with large amount of water during at least 15 minutes and contact medical help.

Skin contact:................................... Clean with water.

Inhalation:........................................ Move victim to fresh air. Obtain medical attention immediately.

Ingestion:......................................... Get medical attention.

Other first-aid measures:................. None.

8. TOXICOLOGICAL PROPERTIES

Route of entry:................................ Inhalation

Toxicity......................................... Oral (LD50): N/A

Skin(LD50)

Vapour(LC50): : 200ppm (Vinyl acetate)

SIMDUT CLASS; No Regulated

Effects of chronic exposure............. Non long term effect known

Effects of acute exposure............... Unknown

9. SPECIAL PROTECTION MEASURES FOR HANDLING AND STORAGE

Required conditions for EPP.............. Normal working conditions.

Eye protection................................. Wear safety glasses with side shields.

Glove requirements.......................... Using chemical resistant gloves is recommended.

Clothing requirement....................... If exposure is severe, wear rubber boots and apron.

Change/removal of clothing.............. Remove contaminated clothing and launder before reuse.

Wash requirements......................... Wash hands before eating, drinking, smoking or using toilet.

Respirator requirements.................. None required if under normal handling conditions. Use approved

NIOSH respirator if vapour or mist levels are irritating.

Ventilation Requirement................... General.

Storage.......................................... No particular storage in normal conditions. AVOID FREEZING

10. NOTICE

All statements, recommendations and technical information contained in this document are based on tests and information which Tec-N-Tec beleives to be accurate at publication. As Tec-N-Tec cannot control application environment, we recommened that buyers conduct their own test. Tec-N-Tec will assume no obligation or liability for results obtained from the use of this product and will not be liable for any direct, indirect consequences or any other damage, except to replace the product and or refund the purchased price to the buyer.

Abbreviations: N/A - Not available N/Ap - Not applicable UN - Unknown

Adhertec

Specialty adhesive tape, Liquid adhesive, Hot-melt glue etc...

Rubans collants spécialisés, Adhésifs liquides, thermofusibles etc...

Duotec

DUOTEC system for I.G gas-filled windows unit manufacturer

Système DUOTEC pour le fabricant de fenêtres isolées au gaz

Rivetec

Blind rivets, Threaded inserts, Solid rivets, Semi-tubular rivets etc...

Rivets aveugles, Ecrous insérés (Threaded insert), Rivets solides, Rivets semi-tubulaires etc...

Webmaster Administrateur du site